Study on vapour dispersion and explosion from compressed hydrogen spill: Risk assessment on a hydrogen plant

Hydrogen produced from renewable resources is one of the cleanest fuels and could be used to store intermittent solar, wind and other energies. The main concern about using hydrogen is its hazards, such as high storage pressure, wide-range flammability, low mass density, and high diffusion. This study investigated the hazards of compressed hydrogen storage by developing a CFD model to understand the gas dispersion behaviour. The model was validated using the past experimental data and showed a good agreement, which could demonstrate the diffusion characteristics and gas stratification of a buoyant gas. A case study of an accidental release of compressed hydrogen from a storage tank was investigated to evaluate the risk of a hydrogen plant. A mathematical model of the jet spill was used to account for the choking effect from a high-pressure release to ensure the input velocity in CFD simulation is suitable for modelling gas dispersion using verified spatial and temporal scales, then the simulation results were used as inputs of vapour cloud explosions (VCEs) to investigate the potential overpressure effect. It was found the CFD model could predict a more reasonable flammable gas amount in cloud than using the bulk hydrogen release rate. The safety distance based on the overpressure prediction was reduced by 35%. The method proposed in this study can provide more validity for the consequence analysis as part of risk assessment.     

Prediction of fish quality level with machine learning

In this study, sea bream, sea bass, anchovy and trout were captured and recorded using a digital camera during refrigerated storage for 7 days. In addition, their total viable counts (TVC) were determined on a daily basis. Based on the TVC, each fish was classified as ‘fresh’ when it was <5 log cfu per g, and as ‘not fresh’ when it was >7 log cfu per g. They were uploaded on a web-based machine learning software called Teachable Machine (TM), which was trained about the pupils and heads of the fish. In addition, images of each species from different angles were uploaded to the software in order to ensure the recognition of fish species by TM. The data of the study indicated that the TM was able to distinguish fish species with high accuracy rates and achieved over 86% success in estimating the freshness of the fish species tested.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Montmorillonite-perlite-iron ceramic membranes for the adsorption/removal of As(III) and other constituents from surface water

In this study, ceramic membranes made of montmorillonite, perlite and iron were used to remove As(III) from water. Membranes prepared with 0.0, 0.5, 1.0, and 1.5 wt% of iron content were used to filtrate As(III) synthetic water and surface water solutions. As(III) adsorption capacity and removal efficiency, and other parameters such as cations and anions content, turbidity, pH, electrical conductivity were used to evaluate the membranes' performance. Results show that the As(III) adsorption/removal capacity of membranes was improved by the addition of iron. Adsorption capacity of 7.5 μg As(III)/g and removal efficiency of 97% can be achieved in membranes with 1.0 wt% of iron filings content for surface water; however, a greater amount of iron in the membrane structure limits the adsorption capacity of As(III). Besides the capacity of ceramic membranes to adsorb/remove As(III), membranes were also effective to remove other ions, turbidity, and electrical conductivity from the surface water. The addition of iron to the ceramic membranes enhanced their capacity to remove such surface water constituents. These results are important from the practical viewpoint showing the potential of ceramic membranes for the removal of metalloids and other water constituents. Langmuir isotherm model best described the adsorption process in ceramic membranes, suggesting that adsorption of As(III) happened on a monolayered surface of the ceramic membrane.     

有砟轨道路基翻浆冒泥模型试验系统的研发与应用

为研究既有线有砟轨道路基的翻浆冒泥机理，自主研发了一套能够模拟循环荷载–湿化耦合作用的模型试验系统。模型试样直径500 mm，由厚度分别为350 mm的路基土和200 mm的道砟组成，整个试样在高强度透明有机玻璃模型筒中制备完成。模型试验系统配备有监测荷载、位移、体积含水率和孔隙水压力的4种传感器，并通过高清相机对颗粒迁移过程进行图像捕捉。基于所研发的试验系统，针对辛泰铁路典型翻浆冒泥病害路段土样，开展翻浆冒泥模型试验。试验结果表明：动孔隙水压力是导致翻浆冒泥病害产生的关键因素。随着体积含水率的增加，动孔隙水压力引起的颗粒迁移量逐渐增加；在饱和状态下，会引起大量颗粒迁移，翻浆冒泥现象显著。试验结束时，道砟污染指数达到25%，在实际工程中已严重影响铁路的正常运营，有必要对污染道砟进行换填。     

不同进水流速对泵站进水池漩涡的影响

为探究泵站进水流速大小与泵站进水池水流流态、漩涡的产生与发展变化规律,结合泵站实际运行情况,建立引渠、前池、进水池和进水管的泵站物理模型和湍流数学模型,采用VOF模型和非定常的SST k-ω湍流模型对9种不同流速的泵站进水水流特性进行数值模拟,分析不同进水流速的泵站进水池水流流场分布、漩涡涡量的变化及分布规律。研究结果表明:当进水流速为0.322 2～0.564 2 m/s时,泵站表面漩涡的强度随进水流速的增大而增强:当进水流速为0.322 2～0.401 6 m/s时,进水池出现Ⅲ、Ⅳ型漩涡;当进水流速为0.483 5 m/s时,进水池出现Ⅴ型漩涡;当进水流速为0.520 8～0.564 2 m/s时,进水池出现Ⅵ型漩涡。将数值计算结果与模型试验结果进行对比,两者基本吻合。研究结果可为泵站工程设计提供参考。     

煤矿水仓清理新工艺

通过调研现场情况以及检测煤泥特性，探寻一种实用性强、方法简单的新工艺来替代劳累的人工和繁琐的机械清淤，解决现实问题。针对实际情况开发清仓新工艺，介绍了该工艺的技术路线选择、设计依据以及实际应用效果。该新工艺具有降低清仓时间、减轻工人劳动强度、设备操作简单、实用性强等特点。     

Microscopic high-speed video observation of oxygen bubble generation behavior and effects of anode electrode shape on OER performance in alkaline water electrolysis

An important difficulty associated with alkaline water electrolysis is the rise in anode overpotential attributable to bubble coverage of the electrode surface. For this study, a system with a high-speed video camera was developed, achieving in-situ observation of bubble generation on an electrode surface, monitoring an area of 1.02 mm² at 6000 frames per second. The relation between polarization curve (current density up to 3.0 A cm^?2) and oxygen bubble generation behavior on nickel electrodes having cylindrical wires and rectangular wires of different sizes (100–300 μm) was clarified. The generated bubbles slide upward, contacting the electrode surface and detaching at the top edge. Observations indicate that small electrodes have short bubble residence time and thin bubble covering layer on the electrode. As a result, the small electrode diameter contributes to smaller overpotential at high current density.     

Novel one- and two-dimensional InSbS3 semiconductors for photocatalytic water splitting: The role of edge electron states

Photocatalytic water splitting has become a promising technology to solve environmental pollution and energy shortage. Exploring stable and efficient photocatalysts are highly desired. Herein, we propose novel low-dimensional InSbS₃ semiconductors with good stability based on density functional theory. Such InSbS₃ structures could be obtained from their bulk crystal by suitable exfoliation methods. Our calculations indicate that two-dimensional (2D) and one-dimensional (1D) InSbS₃ nanostructures have moderate band gaps (2.54 and 1.97 eV, respectively) and suitable band edge alignments, which represents sufficient redox capacity for photocatalytic water splitting. 2D InSbS₃ monolayer possesses oxygen evolution reaction (OER) activity and 1D InSbS₃ single-nanochain possesses hydrogen evolution reaction (HER) activity under acidic conditions. Interestingly, two edge electron states can be introduced when the dimension of InSbS₃ is reduced from 2D to 1D and the new electron states can exist in arbitrary-width nanoribbons, which can effectively promote the process of HER. Moreover, InSbS₃ monolayer and single-nanochain also exhibit large solar-to-hydrogen efficiency, high carrier mobility, and excellent optical absorption properties, which can facilitate the process of photocatalytic reactions. Our findings can stimulate the synthesis and applications of low-dimensional InSbS₃ semiconductors for overall water splitting.